6000 Miles
- Carry out preliminary Test Drive
- Check Seat Belts operation and mountings
- Check operation of all electrical systems (including Alarm and Air Conditioning)
- Remove all road wheels and apply anti-seize compound to hubs and wheel studs
- Check Hand Brake operation and lever security; adjust and lubricate if necessary
- Visually inspect brake Pads for wear, callipers for leaks and condition of Flexi-Hoses
- Measure and record Brake Disc thickness
- Offside Front (mm)
- Nearside Front (mm)
- Offside Rear (mm)
- Nearside Rear (mm)
- Carry out Brake Fluid Boiling Point test and record result
- Check Brake Fluid Level
- Visually check fuel, clutch, brake pipes and unions for chafing, corrosion and correct routing
- Visually check all drive shafts
- Visually check Diff mounting bolts
- Change fuel filter
- Change gearbox oil
- Change engine oil and filter
- Change Diff oil
- Check / top up gearbox oil
- Check / top up diff oil
- Check Exhaust System Condition
- Check condition of steering joints, rack gaiters, ball joints and wishbone bushes
- Check for fluid leaks from hydraulic pipes and unions (Power Assisted Steering only)
- Visually check tyres/ road wheels for damage; record tyre tread depth and refit to original position.
- Visually inspect all suspension fixings for security
- Visually check complete underside of vehicle for faults and abnormalities
- Visually check security of manifold bolts
- Check security of Rocker Covers
- Change Spark Plugs
- Check Distributor Cap, Ignition leads and low tension leads for deterioration
- Check Crank sensors for debris
- Check Engine Sensor Connections for Corrosion
- Check Drive Belts condition; Adjust /Change if required
- Check Air Cleaner element
- Remove Air Filter, inspect, clean and apply protective oil
- Check the condition of the engine and gearbox mounting rubbers
- Check throttles and linkage operation and lubricate where possible
- Check / adjust Throttle Stop
- Check / top-up Power Assisted Steering Fluid (where applicable)
- Check / top up Clutch Fluid
- Change Clutch Fluid
- Check / top up windscreen washers and check wiper blades for condition
- Check Master Cylinder and under bonnet grommets are sealed; reseal if required
- Check Engine breather/ hoses for security and condition
- Check / adjust ignition timing and carbon emissions with engine operating at temperature
- Check/ Adjust engine setting on Computer with engine at operating temperature
- Pressure Check Cooling system, for leaks. Hoses for security
- Check Cooling Fan operation
- Check / adjust tyre pressure (including spare wheel)
- Check headlight alignment and aux lights if fitted
- Visually check front and rear tyres evidence of uneven tyre wear due to incorrect tracking or camber settings
- Wash wheels, repaint brake callipers and discs where applicable
- Check / lubricate all hinges, doors, boot and bonnet locks and catches
- Road test vehicle
- Visually check steering wheel is centralised
- Carry out Service Valet
- Stamp Service Book.
12000 Miles
- Carry out preliminary Test Drive
- Check Seat Belts operation and mountings
- Check operation of all electrical systems (including Alarm and Air Conditioning)
- Remove all road wheels and apply anti-seize compound to hubs and wheel studs
- Check Hand Brake operation and lever security; adjust and lubricate if necessary
- Visually inspect brake Pads for wear, callipers for leaks and condition of Flexi-Hoses
- Measure and record Brake Disc thickness
- Offside Front (mm)
- Nearside Front (mm)
- Offside Rear (mm)
- Nearside Rear (mm)
- Carry out Brake Fluid Boiling Point test and record result
- Check Brake Fluid Level
- Visually check fuel, clutch, brake pipes and unions for chafing, corrosion and correct routing
- Visually check all drive shafts
- Visually check Diff mounting bolts
- Change fuel filter
- Change gearbox oil
- Change engine oil and filter
- Change Diff oil
- Check / top up gearbox oil
- Check / top up diff oil
- Check Exhaust System Condition
- Check condition of steering joints, rack gaiters, ball joints and wishbone bushes
- Check for fluid leaks from hydraulic pipes and unions (Power Assisted Steering only)
- Visually check tyres/ road wheels for damage; record tyre tread depth and refit to original position.
- Visually inspect all suspension fixings for security
- Visually check complete underside of vehicle for faults and abnormalities
- Visually check security of manifold bolts
- Check security of Rocker Covers
- Change Spark Plugs
- Check Distributor Cap, Ignition leads and low tension leads for deterioration
- Check Crank sensors for debris
- Check Engine Sensor Connections for Corrosion
- Check Drive Belts condition; Adjust /Change if required
- Check Air Cleaner element
- Remove Air Filter, inspect, clean and apply protective oil
- Check the condition of the engine and gearbox mounting rubbers
- Check throttles and linkage operation and lubricate where possible
- Check / adjust Throttle Stop
- Check / top-up Power Assisted Steering Fluid (where applicable)
- Check / top up Clutch Fluid
- Change Clutch Fluid
- Check / top up windscreen washers and check wiper blades for condition
- Check Master Cylinder and under bonnet grommets are sealed; reseal if required
- Check Engine breather/ hoses for security and condition
- Check / adjust ignition timing and carbon emissions with engine operating at temperature
- Check/ Adjust engine setting on Computer with engine at operating temperature
- Pressure Check Cooling system, for leaks. Hoses for security
- Check Cooling Fan operation
- Check / adjust tyre pressure (including spare wheel)
- Check headlight alignment and aux lights if fitted
- Visually check front and rear tyres evidence of uneven tyre wear due to incorrect tracking or camber settings
- Wash wheels, repaint brake callipers and discs where applicable
- Check / lubricate all hinges, doors, boot and bonnet locks and catches
- Road test vehicle
- Visually check steering wheel is centralised
- Carry out Service Valet
- Stamp Service Book.